新闻中心

EEPW首页 > 嵌入式系统 > 设计应用 > 基于PIC16F84的两组PWM输出的实例源程序

基于PIC16F84的两组PWM输出的实例源程序

作者:时间:2012-08-12来源:网络收藏

产生两组

本文引用地址:http://www.amcfsurvey.com/article/171049.htm

;**********************************************************************
list p=16F84 ; list directive to define processor
#i nclude p16F84.inc> ; processor specific variable definitions

__CONFIG _CP_OFF _WDT_OFF _PWRTE_OFF _RC_OSC

; '__CONFIG' directive is used to embed configuration data within .asm file.
; The lables following the directive are located in the respective .inc file.
; See respective data sheet for additional information on configuration word.


;********************** CONST DEFINITIONS******************************
FULL_WORK = 10 ;
DEF_WORK1 = 2 ;
DEF_WORK2 = 8 ;
PORT_OUT = PORTB ;
PIN_1 = 0 ;
PIN_2 = 1 ;
;********************** VARIABLE DEFINITIONS***************************
CBLOCK 0x0C
w_temp ; variable used for context saving
status_temp ; variable used for context saving
PWM_FULL ;
PWM_WORK_CFG1 ;
PWM_WORK_CFG2 ;
PWM_WORK_CNT1 ;
PWM_WORK_CNT2 ;
ENDC
;**********************************************************************
;****************** ***********************
;**********************************************************************
ORG 0x000 ; processor reset vector
ResetStart
goto main ; go to beginning of program
;**********************************************************************
;****************** *************************
;**********************************************************************
ORG 0x004 ; interrupt vector location
movwf w_temp ; save off current W register contents
movf STATUS,w ; move status register into W register
movwf status_temp ; save off contents of STATUS register

bsf STATUS,RP0
bcf INTCON,T0IF ;
bcf STATUS,RP0

decfsz PWM_FULL,F ;
goto ISR_PWM1
bsf PORT_OUT,PIN_PWM1 ;
bsf PORT_OUT,PIN_PWM2
movlw FULL_WORK ;
movwf PWM_FULL
movf PWM_WORK_CFG1,W
movwf PWM_WORK_CNT1
movf PWM_WORK_CFG2,W
movwf PWM_WORK_CNT2
goto ISR_EXIT
ISR_PWM1
decfsz PWM_WORK_CNT1,F ;
goto ISR_PWM2
bcf PORT_OUT,PIN_PWM1 ;
ISR_PWM2
decfsz PWM_WORK_CNT2,F ;
goto ISR_EXIT
bcf PORT_OUT,PIN_PWM2 ;
ISR_EXIT
movf status_temp,w ; retrieve copy of STATUS register
movwf STATUS ; restore pre-isr STATUS register contents
swapf w_temp,f
swapf w_temp,w ; restore pre-isr W register contents
retfie ; return from interrupt
;**********************************************************************
;**********************************************************************
InitPWM
bsf STATUS,RP0 ;
bcf PORT_OUT,PIN_PWM1
bcf PORT_OUT,PIN_PWM2
bcf STATUS,RP0
bsf PORT_OUT,PIN_PWM1 ;
bsf PORT_OUT,PIN_PWM2
movlw FULL_WORK ;
movwf PWM_FULL
movlw DEF_WORK1
movwf PWM_WORK_CFG1
movwf PWM_WORK_CNT1
movlw DEF_WORK2
movwf PWM_WORK_CFG2
movwf PWM_WORK_CNT2
retlw 0

pwm相关文章:pwm是什么


pwm相关文章:pwm原理



上一页 1 2 下一页

评论


相关推荐

技术专区

关闭